SZ Crossing Ruby Wireless Ball Vaporizer

IN THE BOX

1x Wireless housing filled with 520 pcs gem cut rubies
1x Titanium bowl with both 14.4mm and 18.8mm glass joints (male)
1x Classic PID controller
1x Dock Station with screws & Allen key
1x 25mm Coaxial Heating Coil
1x Large Scoop
1x Wooden Handle Brush
1x Power cord
2x Mesh screens for Titanium bowl
2x Viton o-rings for Titanium bowl

How to set up

Step 1. Plug in the heating coil. Into the round plug at the rear of the unit. Plug in the
power cord into the rear of the unit. *Make sure both the power cord and the
heating coil are securely connected.*

Step 2. Wrap the heating coil cord carefully around the cable management lugs of
the docking station. Place the other end of the heating coil into the top slot of the
dock station and fix with the two screws provided, using the Allen key. Tighten so the
heating coil is snug and secure.

Set the temperature

Just use the up and down arrows. *The suggested vape
temperature range is 510-560 Fahrenheit.*
Burn off the manufacturing oil: DO ONCE BEFORE USE! ONLY.
Before the first use, put the wireless housing into the heating coil and heat to 600f
for 15-20 minutes. This is to burn off any residue from manufacturing. You are only
required to do this once.

How to use

Load desired flower to the Titanium bowl using the provided scoop. Use the base of
the spoon to pack it down gently for even heat distribution.
*Don't pack too tightly or you will restrict airflow.*

Once the wireless housing is placed in the heating coil, allow time for the wireless
housing to heat soak, this can take around 10 minutes depending on your
preference.

After heat soak

Once ready, place the wireless housing inside your Titanium bowl and begin your
inhale. You can clear the entire bowl with a single pull, or do it in 2-3 based on your
draw and temp.

Repeat as desired. When the session finished, empty the bowl and use the wood
brush to clean the screen.You can use the wireless housing as injector or diffuser onto the titanium bowl as your preference. The housing is also compatible with the glass Thermal/Ruby Twist Bowl (injector side) and Thermal/Ruby Twist Microdose Diffuser Bowls (injector side).

The dock station has 3 slots for 18mm joints, 4 slots for 14mm joints and 2 slots for
10mm joints to stock with bangers, bowls, or accessories. The Titanium bowl comes with 14.4mm glass joint (pre-installed) and 18.8mm glass joint included with the kit. You can switch the glass joints to fit your glass as desired.

Note: The joints on these bowls can be quite stiff to remove. We've found the best
way is to grip the glass joint and bowl firmly then pull steadily apart, don't wiggle or
twist. Once it's apart you can add a little o-ring lubricant to the o-rings to make it
easier the next time. If you're really having trouble, you can use thermal expansion to
assist; place your wireless housing onto the bowl for around 15 seconds to heat it up,
then hold the titanium part with an oven glove or towel and pull the glass joint out as
described here.

Available Bowls

Thermal Twist Glass Bowl: Features a 14.4mm male joint and a convenient side-carb design, offering a max capacity of approximately 0.4g. Get it here

Microdose Diffuser Bowl: A versatile option for smaller sessions. Combines induction and convection heating and also allows the use of concentrates by placing material on the screen, securing it with an additional screen. With proper heat soaking, this setup delivers impressive results. Get it here 

Titanium Matrix Bowl: Ideal for hybrid-style hits, this bowl excels at heat retention and can be heat soaked without getting stuck in glass joints. Get it here

Warnings

Do not touch the heater coil unless it has fully cooled
Do not touch the metal of the housing, only the wooden handle
Keep away from water and high humidity

Disclaimer

Crossing Tech and its retailers are not responsible for the use or misuse of this
product. The WOHW is intended for use with legal materials only.
If any parts damaged please cease use and contact your retailer.

Warranty

The Heater Coil and PID Controller come with a one year manufacturer warranty
against defects. Please contact your retailer to place a warranty claim.